Search results

Pala June 2020 fox raceway main track

1:20ish that mini rider was closer than it felt to me. I’m glad he didnt keep going across the track more. :oops:

Riding cahuilla Creek Mx main track with @TCMB371

We just bought a couple of Stacyc bikes for our kids, 2 and 4. They are an awesome bike for young kids to transition from a bicycle/balance bike to a moto bike. STACYC Stability Cycle We first got an oset for our oldest but it was too much for her to learn throttle control. The Stacyc 16e is...

For the display board, you can add the far lower right button will display hours when pressed. Lower right button changes miles to hours while pressed. maybe add the suspension types...4CS, AER, xplorer? Or all the firmware information?

Pala/ fox raceway May 2020, video of my second time out on the track. All new layout and looks like they cleaned up some sections from when they first changed is last week from the video I watched. track broke down pretty quick but a fun track for the most part.

Cahuilla creek motocross track may 2020

Post a picture of the loader tab. Did you copy the recommended_fw.json and firmware(s) to the /.alta/firmware folder? do you have an A battery or a R battery pack?

I asked if Alta motors were supported and didn’t really get a yes or no answer.... “The initial VCU release will support Cascadia inverters, which can be used to control a wide variety of motors. We will be continually adding to the list of supported inverters going forward with the aim of...

The Sm caliper uses a different bolt pattern, I would suggest you buy a complete stock exr or mxr front brake setup. The lower fork lugs are different in a few ways; large axel vs small axle and the Sm caliper bots towards the fork leg and the mxr/exr caliper bolts perpendicular to the fork leg.

Sold

I just released I didn’t really answer your question. The entire rear tails section/subframe can be swapped between sm and mxr. The mxr just will not have the lights or bolts to hold the lights. I tried to put a mxR shock on the older bike (sm,rx,MX frame) Picture of a mxr subframe I cut to...

The mxr rear shock will not direct bolt on to the sm. You have to cut the subframe because the top of the shock will hit the subframe. I believe the frame is different. the subframe and rear fender seemed like it was the same but the shock mount was different on the sm compared to the mxr.

People at my work did this and they said it was easy to do using a t shirt. I have been using a snowboarding neck covering and just pull it up over nose. For those of you that wants an airfliter, check theses out. “ UNI Filter (714) 535-6933 Part # FFM-6. $9.95 pack of 6.”

Hmmm it s in November, so I can race the 40+ class since it after my bday this year. let me know what class you guys end up racing and maybe I’ll go this year. 🤔

Yeah but parking area was huge so we had a lot of room away from people between motos

LACR today April 2020 Last track open in my area (2.5 hour drive each way)

I am going to sell my 2018 MXR with a light harness with tail and handle bar wire harnesses. You would need to get a head light, tail light kit and horn if you wanted to get it plated. I also bought the DMV emission stickers that have the VIN on them. PM me for more details.

Why didnt you Guys use one of the two shippers that people on here have used recently? These companies just roll the bike into the truck. Pretty simple. Home - HAULBIKES $525 shipping special MOTOSHIPPERS - MOTOSHIPPERS.COM $700 ish to ship.

I bought that foot and it was a super tight foot. Such a pain in the ass to rubber mallet in. Took like 10 minutes to get it to seat. Not sure if there is a trick. Otherwise it looks fine and holds the bike up in the garage haha. I also bought a Ktm rubber strap to hold the stand up when I...