Search results

the coolant and oil were recently changed,as well ans the chain and sprocket, suspesion is setup for a 185lbs rider. runs awesome. a diag cable and rapid charger is included. asking 8800

so there is the alta shroud stl(for anyone that wanted to print one), its smoothed alittle bit, and itll need a little bit of work if you want to print it.

yes i can, i have been printing the alta and ktm parts and modeling them but so far i havent got anything i like lol. the biggest side is 510mm so you need a big printer(min 450x450x500mm), which mine prints the whole shroud just fine.

I'm already been working on that, i have a professional scanner, and ive modded them a ton i just havent figured out a design i like.

with a conventinal frame that's possible, but with the contours of the alta frame flat is not an option with the frame covered(without the bike being super fat), and even without it not. Im going for less of a point than the stock shrouds though, but i also want it to look good. It'll have more...

so i ordered some graphics to cover the frame from @fammxdesign, I'm toying with the idea of having the frame exposed, but I still havent found a design(i have over 10, frame covered ,ive tried ) i like or id have one printed to show.

does anyone have part# for the mxr rear linkage bearings and seals?

i did a quick scan and quick cutout(if i was going to actually make it, i would have put time in designing them lol) but thats to show the idea of handles that i wish they did to move the bike or for tricks.(but if the number plates are removed there is a good spot to grab on ether side.

I figured they did cause on my mx i hated that I wanted power all the time like a Ice, but i couldnt get a good answer back then, but I thought the mxr did it also but since i regeared it its not as noticeable. thats my only complaint power wise over a Ice.

my issues with them is if you ride the bike hard, the rear tire hits the fender and breaks the plastic, thus ripping out the inserts, its a weird design imo also i wish they did a handle or 2 on the sub frame. I have plastic welded, and epoxied. mine but im not sure how long thatll last.

the way the battery is built as long as the brd sees voltages and is happy with the temp signals, any type of battery could be made to work in the modules, Ive though about that same thing about solid state modules, and after playing withi the bcu It should be possible. my bike runs great so i...

Pilot Details Height: 6' Weight:180lbs Skill level/Class: not sure but i use most of the power of my mxr Riding type (MX, SX, Trails, Desert, etc): mostly single track with mx sometimes Bike information Year:2018 Model: mxr Forks Fork Type (4CS, AER48, or specify other): aer48 Fork Position in...

so Ive been looking at the inverter firmware and if there is someone that knows assembly really well, here is a little of it. but does anyone know what microprocessor the inverter uses?

mine had a code 37 thats just the humidity sensor malfuction unless you actually have water/humidity in the battery, because the honeywell sensor they used doesnt like light at all, but they put it really close to a led, so it causes the code 37 false codes. i installed a spliter to block the...

yes and a huge thanks btw(its running awesome since), but that brd is what controls the modules and voltage shown in the multitool and display. With the help of @Mark911 I figured out how simple these bikes are actually built.

been super busy, but there's another alta piece. slowly getting there(i do have the ktm part mocked up though)

its all in the owners manual, and the bcu will not send the 328v or so volts depending on charge across the orange connector without the bike turned on. 2017 & 2018-2019 Alta Redshift Owners Manual

It was bcu issues. big thanks to @Mark911 for all the help to get it all figured out, once the new chips show up it should be cruising again.

well got around to printing one of the alta pieces lol, a few more to go and i can mock some stuff up, and hopefully get it to where i like it so i can print a shroud to test.

I wish that would make what im Trying to do much easier, that and i wish i had all the schmatics also.